Skip to content

XenCenter

About this Document

This manual is intended for system administrators. It explains how to install the AXS Guard virtual appliance using a Citrix XenCenter Client.

Xen Logo

Before you Begin

Prerequisites

  • A Xen Server with an AXS Guard ISO image. Refer to your server documentation for information about adding installation sources to your Xen environment.

  • A XenCenter client. Refer to your Citrix documentation for installation and configuration instructions.

VM Requirements

  • The virtual machine must be configured for a 64-bit guest operating system.

  • System memory: assign the amount of memory allowed by your license. See our system specifications. At least 1 GB is required if you are using an evaluation license.

  • Only 1 HDD is allowed with a capacity of at least 100 GB. For appliances in a High Availability configuration, a minimum of 200 GB is required.

  • The number of NICs is determined by your system license. A maximum of 10 NICs is supported.

Important

If you are running XenServer 6.1.0, please install hotfix XS61E020.

Creating a new VM

  1. Start your Citrix XenCenter client.

  2. Go to VM > New VM or press Ctrl-N

    New VM

  3. Select Other install media and click next.

    VM Template Selection

  4. Enter a name for the new VM. The description is optional. Click next to continue.

  5. Check Install from ISO library or DVD drive (default) and select the AXS Guard installation image file.

    Selecting the Installation Source

  6. Select Place the VM on this server. Make sure there is enough memory available, otherwise the installation will fail.

    Selecting the Installation Target

  7. Set the number of CPUs to 1. 512 MB of RAM is the required minimum. Click next to continue.

    CPU and Memory Configuration

  8. Check Use these virtual disks and click on Add to configure the VM storage.

  9. Enter a name for the new virtual disk. Make sure the size is at least 40 GB.

    Storage Configuration

  10. Use autogenerated MAC for your network devices.

    Network Configuration

  11. Finish your setup and start the VM automatically.

    Finishing Up

Installing your Virtual Appliance

First Boot

When booting the ISO file for the first time, you will be prompted to install the AXS Guard OS.

Boot

Partitioning the Hard Drive

  1. When starting up for the first time, the system will ask you to partition your hard drive. Simply enter yes.

  2. After partitioning the appliance’s hard drive, the software packages will be installed automatically.

    image

Important

Please be patient. Do not turn off your virtual appliance while the hard drive is being partitioned. The installation of the packages takes a while. The machine will halt when the installation is finished.

Booting up the AXS Guard OS

  1. Select the storage tab and eject the iso image.

    Ejecting the Installation Image

  2. Select the console tab and double-click on the icon of your machine to boot it up.

    XenCenter will automatically boot the virtual version. The following message will appear when your appliance is ready for use: AXS Guard up and running

    Booting up your Appliance

  3. Configure the appliance’s network settings as explained in the next section.

Network Configuration

After booting up, you must configure the AXS Guard’s network devices via the console tool in order to be able to access its web-based administrator tool. The factory default LAN IP address of the AXS Guard appliance is 192.168.250.254/24.

  1. After booting up, press Alt + F2 to go to a console.

  2. Log in with the following credentials:

    • User: sysadmin

    • Pass: sysadmin

  3. Select Network > Configuration.

  4. Configure your network devices.

    image

  5. Reboot the virtual appliance to apply the network configuration changes.

  6. Log in to the web-based administrator tool of the virtual appliance as explained below.

Logging in to the Configuration Tool

  1. Start your favorite browser

  2. Enter the following in the URL field: https://appliance_LAN_IP:82

  3. Accept the self-signed certificate.

  4. Log in with the following credentials:

    • Username: sysadmin

    • Password: sysadmin

    image

  5. Follow the instructions in the getting started guide and other feature manuals to further configure your appliance.

Support

If you encounter a problem

If you encounter a problem with AXS Guard, follow the steps below:

  1. Check the troubleshooting section of the feature-specific manual.

  2. Check the knowledge base on this site for information about special configurations.

  3. If no solution is available in any of the above sources, contact your AXS Guard vendor.

Contact Information

(+32) 15-504-400
support@axsguard.com